STM8

Compiler Comparison
RTOS Availability

Tutorials

STM8L-DISCOVERY

LED Timer
Serial

STM8S-DISCOVERY

LED Timer
Serial

STM8A-DISCOVERY

STM8AF LED Timer
STM8AF Serial
STM8AF Benchmarks
STM8AL LED Timer
STM8AL Serial

EX-STM8-Q64a-207

LED Timer
Serial
Benchmarks

Open8S208Q80

LED Timer
Serial
Benchmarks

EX-STM8-Q48a-105

LED Timer
Serial

STM8/128-EVAL

LED Timer
Serial
Benchmarks

STM8L101-EVAL

Serial

colecovision.eu

ColecoVision

STM8

MCS-51

LLVM+SDCC

Contact

Getting started with STM8 development using free software: Serial output on the sduino UNO

This short tutorial presents a simple "Hello World" program for the sduino UNO board. The author used a Debian GNU/Linux system, but the tutorial should work for other Linux distributions, *BSD or other Unices.

The tools we use are

Hardware setup

sduino UNO

The sduino UNO is connected to power and for serial I/O via a USB cable. To write our program to the board, an ST-Link v2 is attached (RESET to RESET on the 8-pin power header, SWIM to pin 7 on the digital I/O header). On the USB end of the serial interface is connected to a computer running a terminal program configured for 9600 baud, no parity, 8 bits, 1 stop bit and no flow control. We used gtkterm.

Get SDCC

Depending on your operating system there might be an easy way to install SDCC 3.5.0 or newer using a package system or similar (e.g. apt-get install sdcc on Debian). While SDCC 3.4.0 should be sufficient for this tutorial, you might want to try a newer version in case you encounter any bugs. In particular, SDCC 3.4.0 has an issue with the library search path; this can be worked around by explicitly specifying the path to the standard library when linking.

SDCC binaries or a source tarball can be downloaded from its website.

Get stm8flash

The stm8flash source can be found at its GitHub location, where there is also a download link for a zip archive of the sources. To compile it, a C compiler, such as gcc, pkg-config and libusb need to be installed. Unzip the archive (e.g. using unzip stm8flash-master.zip) change into the directory stm8flash-master and type make. In case there are any errors, such as header files not found, check that pkg-config and development files for libusb are installed.

The Demo

We present a simple Demo that repeatedly outputs "Hello World!" on UART2 (the only UART the STM8S105 has). This demonstrates setting up and using the UART for serial I/O. Here is the C code:

// Source code under CC0 1.0
#include <stdint.h>
#include <stdio.h>

#define CLK_DIVR	(*(volatile uint8_t *)0x50c6)
#define CLK_PCKENR1	(*(volatile uint8_t *)0x50c7)

#define UART2_SR	(*(volatile uint8_t *)0x5240)
#define UART2_DR	(*(volatile uint8_t *)0x5241)
#define UART2_BRR1	(*(volatile uint8_t *)0x5242)
#define UART2_BRR2	(*(volatile uint8_t *)0x5243)
#define UART2_CR2	(*(volatile uint8_t *)0x5245)
#define UART2_CR3	(*(volatile uint8_t *)0x5246)

#define UART_CR2_TEN (1 << 3)
#define UART_CR3_STOP2 (1 << 5)
#define UART_CR3_STOP1 (1 << 4)
#define UART_SR_TXE (1 << 7)

int putchar(int c)
{
	while(!(UART2_SR & UART_SR_TXE));

	UART2_DR = c;

	return(c);
}

void main(void)
{
	unsigned long i = 0;

	CLK_DIVR = 0x00; // Set the frequency to 16 MHz
	CLK_PCKENR1 = 0xff; // Enable peripherals

	UART2_CR2 = UART_CR2_TEN; // Allow TX and RX
	UART2_CR3 &= ~(UART_CR3_STOP1 | UART_CR3_STOP2); // 1 stop bit
	UART2_BRR2 = 0x03; UART2_BRR1 = 0x68; // 9600 baud

	for(;;)
	{
		printf("Hello World!\n");
		for(i = 0; i < 147456; i++); // Sleep
	}
}

SDCC is a freestanding, not a hosted implementation of C, and allows main to return void. The printf() from the standard library uses putchar() for output. Since putchar() is device-specific we need to supply it. In this case we want it to output data using UART1.

The demo can be compiled simply by invoking SDCC using sdcc -mstm8 --std-c99 serial.c assuming the C code is in serial.c. The option -mstm8 selects the target port (stm8). An .ihx file with a name corresponding to the source file will be generated.

Put the demo onto the board

Assuming stm8flash and serial.ihx are in the same directory, the board is attached through an stlinkv2 device, ./stm8flash -c stlink -p stm8s105k6 -w serial.ihx will write the demo onto the board. You can see the "Hello world" using a terminal program configured for 9600 baud, no parity, 8 bits, 1 stop bit and no flow control.


More about stm8flash

stm8flash was written by Valentin Dudouyt. It works both with stlink (including the one integrated on the discovery boards) and stlinkv2 devices. The programmer can be selected using -c stlink or -c stlinkv2. The target device is selected using the -p option (to get a list of target devices, use the -p option with an option argument that is not an stm8 device, e.g. -p help. stm8flash will treat filenames ending in .ihx or .hex as Intel hex, and other filenames as binaries.

More about SDCC

SDCC was initially written by Sandeep Dutta for the MCS-51, and has a relatively conservative architecture (see Sandeep Dutta, "Anatomy of a Compiler", 2000). It has been extended by various contributors and more recently, incorporated some cutting-edge technologies, in particular in register allocation (see Philipp Klaus Krause, "Optimal Register Allocation in Polynomial Time", 2013). The stm8 backend was mostly written by Philipp Klaus Krause for his research into bytewise register allocation and spilling (see Philipp Klaus Krause, "Bytewise Register Allocation", 2015).

SDCC is a C compiler that aims to be compliant with the C standards.

Important compiler options for STM8 developers include: